Light Up Toyota Emblem
5D LED Light Up Toyota Emblem Front &Tail Light

5D LED Light Up Toyota Emblem Front &Tail Light


(2 customer reviews)
Add any 2 products to the cart to get a Free LED roof star lights!

Free worldwide shipping on all orders 

  • 30 days easy returns
  • Order yours before 2.30pm for same day dispatch
Guaranteed Safe Checkout

Light Up Toyota Emblem Description:

【Applicable for Toyota】The appearance of this product is consistent with the original car standard, and it can be directly replaced by the original car standard when installed in the car tail box. Its special vacuum plating technology not only ensures the same gloss as the original logo, but also ensures high transparency and uniform brightness.

【High Quality】 It adopts high-quality LED lamp set, featuring high brightness and long service life. It is specially designed to be waterproof and dust-proof to ensure long-term use.

【Unique design】This product is specially designed for car modification enthusiasts. When the daytime car light is not bright, there is no difference with the original car standard. When the night license plate lighting is turned on, the LED car light will also light up, making the car Marked in the night to become dazzling, rich in future technology, highlighting the noble blood of your car.

【Easy Installation】 Use high-quality car special double-sided adhesive, strong and strong lasting!The LED light inside is specially waterproof and dust-proof! LED lamps have a lifespan of up to 100,000 hours.

Note: this product is suitable For for all Toyota of cars

155858 LED Emblem 1

Light Up Toyota Emblem Feature:

Voltage:12 (V)

14 x10 cm/15 x 10 cm/16 x 11cm
5.51 x 3.94 in / 5.91 x 3.94 in / 6.30 x 4.33 in

10 x 6.8 cm/11 x 7.5 cm/11.7 x 8.2 cm/12 x 8 cm/13 x 8.9 cm
3.94×2.68 in /4.33×2.95 in / 4.61×3.23 in / 4.72×3.15 in/ 5.12×3.50 in

No.1: Camrys, EZ, Corolla, old Reiz, Vios (14 x 10 cm)
No.2: new Reiz, Yaris, Alrhard (15 x 10 cm)
No.3: Prado, EZ, VIGO, Highlander, RAV4 (16 x 11 cm)

Wiring length: 0.6 meters
Material: ABS plating, 3M glue at the bottom

Package Contents:1*  Light Up Toyota Emblem

Avoid giving children a play. Do not accidentally install or disassemble this product during driving.

[Tools prepared before installation] Please have the following tools ready before you start:

1. Flat head screwdriver 2. Phillips screwdriver 3. Insulating tape 4. Towel 5. Pliers

【Light Up Toyota Emblem Installation】

1. First place a towel next to the tailgate logo, use a flat-blade screwdriver to shake the logo, and towel to prevent scratching the body.

2. Pay attention to peeling off the double-sided rubber first. When the squatting is moderate, don’t be too fierce.

     After a little bit, slowly squat down, clean the car logo and the double-sided tape on the body.

3. Use a Phillips screwdriver to remove the partition inside the tail box. Note that there are clips in some places. Be careful to remove the baffles to see the various lines.

4. Now install the car standard light, the car standard light power line passes through one of the car standard positioning holes,
and wears the single-sided glue on the back of the car standard light inside the car box. While pulling the wire, the car mark light is glued to the vehicle body, and the pressure is pressed. tight.

5. The car light is installed, and now it is connected to the power supply. The car light should be connected to the power supply of the license plate, so that when the night light is turned on the car light will be turned on at the same time, and the power connector of the rear license plate light is found.

 Not Enough for your car decor? Check this Toyota Door Sill Lights:

Due to the light and screen setting difference, the item’s color may be slightly different from the pictures.


Additional information


Blue, Red, White


3.94×2.68 in, 4.33×2.95 in, 4.61×3.23 in, 4.72×3.15 in, 5.12×3.50 in, 5.51 x 3.94 in, 5.91 x 3.94 in, 6.30 x 4.33 in

2 reviews for 5D LED Light Up Toyota Emblem Front &Tail Light

  1. Adam W. Anderson

    Parts fit perfectly and the result is a very high quality mod. I ran a power cable all the way to the engine bay and hooked it to one of my rocker switches. will not work correctly if you try to use it as a brake light

  2. Daniel Masity (verified owner)

    Great quality and perfect fitment! I’ve wired it to my parking lights when they switch on, very happy!!

Add a review

Your email address will not be published. Required fields are marked *